Extrutech Plastics, Inc.
5902 West Custer Street
Manitowoc, WI 54220

Toll Free: 888.818.0118
Phone: 920.683.5201
Cell: 920.323.3312
Email: info@epiplastics.com
Website: www.epiplastics.com
Print Back
Extrutech Plastics provides a number of high quality panel trims that give your project a clean finished look. To view these trim options click on the photo or blue high-lighted text. Trims are available with a non-painted finish in 8', 10'.12', 14', 16' foot lengths, color matched to requested panels, Cut with standard power saw and a fine tooth blade. Fasten with appropriate trim or truss head screws and construction adhesive per installation instructions or industry standard.
Bullnose Outside Corner Trim
Unit of Measure
Items Wainscoting or Wall Panel Chair Rail Trim
WM390
Wainscoting or Wall Panel Chair Rail Trim 		Wall Panel Base and Cap J-Trim
P0100
J-Trim - perimeter wall trim 		Wall Panel Outside Corner Trim
P0220
Outside Corner, wall trim, 		Two Part H-Bar 3in Cap
P0240
3" Cap, Two Part H-Bar Trim 		Two Part H-Bar Cap and Base Trim
P0241
Base, Two Part H-Bar Trim
Description N/A Extrutech Chair Rail, Item # WM390 for use as a wainscoting cap or decorative molding is made of an exterior grade, hard, dense, engineered polymer, with a smooth surface of a standard chair rail profile. Is 2 9/16" deep by 1 3/16" thick. To cap 1/2" thick wall panels with its 3/8" thick by 1/2" wide cap area. Cut with standard power saws use a fine toothed blade. Fasten with finish nails, trim screws 16"-24" OC. or construction adhesive. Non-painted in white or beige, ready for an acrylic latex based paint, after cleaned and prepped; available in 12'-18' foot lengths, with a weight of 0.4 lbs per foot. N/A Extrutech Plastics J-Trim, Item # P0100 for use as an perimeter wall trim or ceiling trim is made of an exterior grade, hard, dense, rigid polymer, with a smooth surface of a 13/16" face area and 3/4" coverage. Is 5/8" x 1 1/2" wide To cover 1/2" thick wall panels. Cut with standard power saw using a fine toothed blade. Fasten with truss head screws 24" OC or construction adhesive per installation instructions or industry standard. Non-painted in white or color matched to our panels, available at 2' increments from 8' - 20' foot lengths, with a weight of 0.08 lbs per foot. N/A Extrutech Plastics Outside Corner Trim, Item # P0220 for use as an outside corner wall trim; is made of an exterior grade, hard, dense, rigid polymer, with a smooth surface of a 5/8" face area and 5/8" coverage. Is 1 1/4" x 1 1/2" wide To cap 1/2" thick wall panels. Cut with standard power saw using a fine toothed blade. Fasten with truss head screws 24" OC or construction adhesive per installation instructions or industry standard. Non-painted in white or color matched to our panels, available at 2' increments from 8' - 20' foot lengths, with a weight of 0.08 lbs per foot. N/A

Extrutech Plastics Two Part H-Bar 3" inch Cap, Item # P0240 for use as a expansion joint trim between panels,- 16' foot on center. This item is made of an exterior grade, hard, dense, rigid polymer, with a smooth surface of a 3" face area and 1 1/8" coverage for each side. Is 9/16" x 3" wide to cap 1/2" thick liner panels. Cut with standard power saw using a fine toothed blade. Fasten with flat head screws 24" OC and construction adhesive per installation instructions or industry standard. Non-painted in white or color matched to our panels, available at 2' increments from 8' - 16' foot lengths, with a weight of 0.15 lbs per foot. Need to use with Item # P0241 Two Part H-Bar Base. 

Note: Fasten ends of Liner Panels through Nailing Fin Slot to each side of (Base P0241) as shown, to allow for expansion. Add Blocking for fasteners as required.

 		N/A Extrutech Plastics Two Part H-Bar Base, Item # P0241 for use as an expansion joint trim between panels -16' foot on center, as panel end connector trim or to allow for removal and reversing of panels. This item is made of an exterior grade, hard, dense, rigid polymer, with a smooth surface of a 3" face area and 1 1/8" coverage for each side. Is 9/16" x 3" wide, to cap 1/2" thick wall panels. Cut with standard power saw using a fine toothed blade. Fasten with truss head screws 24" OC and construction adhesive per installation instructions or industry standard. Non-painted in white, available at 2' increments from 8' - 16' foot lengths, with a weight of 0.15 lbs per foot. Need to use with Item # P0240 Two Part H-Bar Cap.
Material N/A Engineered Polymer N/A Engineered Polymer N/A Polyvinyl Chloride (PVC) N/A Engineered Polymer N/A Engineered Polymer
Color1 N/A Beige White N/A Beige Caribbean Blue Gray Kelly Green Rocket Red Sunshine Yellow White N/A Beige Caribbean Blue Gray Kelly Green Rocket Red Sunshine Yellow White N/A Beige Caribbean Blue Gray Kelly Green Rocket Red Sunshine Yellow White N/A White
Available Lengths N/A 12 ft14 ft16 ft18 ft N/A 10 ft12 ft14 ft16 ft18 ft20 ft8 ft N/A 10 ft12 ft14 ft16 ft18 ft20 ft8 ft N/A 10 ft12 ft14 ft16 ft8 ft N/A 10 ft12 ft14 ft16 ft8 ft
  • 1 A 20% charge will be added for custom cuts, and /or colors. Volume discounts are available.